Trane Commercial HVAC

A 70kW unit for 208-volt, three-phase operation Applied as an auxiliary heat source in walkways, stairways, vestibules, and entrances. The horizontal and vertical spot heater may be used in commercial, industrial and institutional applications. A specially designed deep-drawn venturi assures uniform air distribution The outward-drawn venturi channels the air forward for maximum, uniform air throw Outlet diffusers are provided to properly direct the heated discharge air

A 80kW unit for 480-volt, three-phase operation Applied as an auxiliary heat source in walkways, stairways, vestibules, and entrances. The horizontal and vertical spot heater may be used in commercial, industrial and institutional applications. A specially designed deep-drawn venturi assures uniform air distribution The outward-drawn venturi channels the air forward for maximum, uniform air throw Outlet diffusers are provided to properly direct the heated discharge air

A 5 kW unit for 208-volt, one-phase operation The surface-mounted heater may be applied in restricted areas or where wall space is limited Use in vestibules, entrance ways, lobbies, restrooms and small office and guard building applications Equipped with zero voltage reset thermal cut-outs for overheat protection and a totally enclosed, permanently lubricated motor

A 15 kW unit for 208-volt, single-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor

Vertical Supply/Return Air Configuration Has a high efficiency 42 Mbtuh scroll variable speed type compressor with a crankcase heater An inverter board for speed control of the compressor is provided Achieves higher efficiency, reduced sound, improved indoor air quality and high reliability through variable speed compressor and fan technology Provides comfort in a wide range of building types and climates Utilizes energy-conserving, heat-recovery capabilities to transfer heat from one area to another to meet individual zone requirements Access for inspection and cleaning of the unit drain pan, coils and fan section is provided

A 5 kW unit for 277-volt, single-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor

A 7.5 kW unit for 240-volt, three-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor

A 25 kW unit for 600-volt, three-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor

Supports four airflow combinations With the vertical configuration, the supply-air is easily converted from a top supply-air to a back supply-air (or vice versa) with a service retrofit kit Provides superior serviceability to maintenance components; indoor air quality standards; sound attenuation; and higher efficiencies rated in accordance to ARI-ISO 13256-1 performance and ASHRAE 90.1 standards  

A 3 kW unit for 240-volt, three-phase operation Designed for rugged industrial applications in hazardous locations where the possibility of explosion or fire exists due to the presence of certain flammable gases, vapors, powdered metals or dusts Permanently sealed, liquid to air, finned tube heat exchanger core Ethylene glycol water mixture used as heat transfer fluid in the heater core, providing -45°C, (-49°F) freeze damage protection High-performance electric motor driven fan blows air across finned tubes to effect uniform heat transfer and area heat distribution Automatic reset capillary type high limit provides high temperature regulation and is rated for 100,000 cycles of service Adjustable louvers allow directional control of air Can be wall, ceiling or floor mounted

A 7.5 kW unit for 480-volt, three-phase operation Designed for rugged industrial applications in hazardous locations where the possibility of explosion or fire exists due to the presence of certain flammable gases, vapors, powdered metals or dusts Permanently sealed, liquid to air, finned tube heat exchanger core Ethylene glycol water mixture used as heat transfer fluid in the heater core, providing -45°C, (-49°F) freeze damage protection High-performance electric motor driven fan blows air across finned tubes to effect uniform heat transfer and area heat distribution Automatic reset capillary type high limit provides high temperature regulation and is rated for 100,000 cycles of service Adjustable louvers allow directional control of air Can be wall, ceiling or floor mounted

A 5 kW unit for 240-volt, single-phase operation With 120 volt control voltage Designed for rugged industrial applications in hazardous locations where the possibility of explosion or fire exists due to the presence of certain flammable gases, vapors, powdered metals or dusts Permanently sealed, liquid to air, finned tube heat exchanger core Ethylene glycol water mixture used as heat transfer fluid in the heater core, providing -45°C, (-49°F) freeze damage protection High-performance electric motor driven fan blows air across finned tubes to effect uniform heat transfer and area heat distribution Automatic reset capillary type high limit provides high temperature regulation and is rated for 100,000 cycles of service Adjustable louvers allow directional control of air Can be wall, ceiling or floor mounted

A 15 kW unit for 240-volt, three-phase operation With 120 volt control voltage Designed for rugged industrial applications in hazardous locations where the possibility of explosion or fire exists due to the presence of certain flammable gases, vapors, powdered metals or dusts Permanently sealed, liquid to air, finned tube heat exchanger core Ethylene glycol water mixture used as heat transfer fluid in the heater core, providing -45°C, (-49°F) freeze damage protection High-performance electric motor driven fan blows air across finned tubes to effect uniform heat transfer and area heat distribution Automatic reset capillary type high limit provides high temperature regulation and is rated for 100,000 cycles of service Adjustable louvers allow directional control of air Can be wall, ceiling or floor mounted

A 15 kW unit for 480-volt, three-phase operation With 120 volt control voltage Designed for rugged industrial applications in hazardous locations where the possibility of explosion or fire exists due to the presence of certain flammable gases, vapors, powdered metals or dusts Permanently sealed, liquid to air, finned tube heat exchanger core Ethylene glycol water mixture used as heat transfer fluid in the heater core, providing -45°C, (-49°F) freeze damage protection High-performance electric motor driven fan blows air across finned tubes to effect uniform heat transfer and area heat distribution Automatic reset capillary type high limit provides high temperature regulation and is rated for 100,000 cycles of service Adjustable louvers allow directional control of air Can be wall, ceiling or floor mounted

Two-point suspension on propeller fan unit heater Provides uniform heating for large open areas in applications such as warehouses, factories and showrooms Lightweight, rugged, compact design is fully accessible for easy installation and maintenance Patented Trane louver cone diffusers allow directional flexibility of heated air Taps the reservoir of heated air which collects at the ceiling level and return it to active service in the floor zone

A 4 kW unit for 240-volt, three-phase operation Architecturally styled and vandal- resistant for schools, churches, stores, office buildings, transportation terminals, dormitories, hospitals Use in vestibules, entrance ways, lobbies, corridors, stairways, reception rooms, rest rooms, offices Equipped with zero voltage reset thermal cut-outs for overheat protection and a totally enclosed, permanently lubricated motor Built-in unit mounted tamper proof thermostat breaks all ungrounded conductors in OFF position

A 5 kW unit for 277-volt, one-phase operation The surface-mounted heater may be applied in restricted areas or where wall space is limited Use in vestibules, entrance ways, lobbies, restrooms and small office and guard building applications Equipped with zero voltage reset thermal cut-outs for overheat protection and a totally enclosed, permanently lubricated motor

A 4 kW unit for 240-volt, one-phase operation The recessed-mounted heater may be applied in restricted areas or where wall space is limited Use in vestibules, entrance ways, lobbies, restrooms and small office and guard building applications Equipped with zero voltage reset thermal cut-outs for overheat protection and a totally enclosed, permanently lubricated motor

The horizontal heat pump features reliable dual scroll compressors, Trane engineered ReliaTel™ controls, computer-aided run testing, and Integrated Comfort™ Systems ReliaTel™ microprocessor controls provide unit control for heating, cooling and ventilating utilizing input from sensors that measure indoor and outdoor temperature and other zone sensors Easy access low voltage terminal board A variety of commercial applications include Office buildings, Schools, Hotels, Apartments/condominiums

A 60kW unit for 240/208-volt, three-phase operation Applied as an auxiliary heat source in walkways, stairways, vestibules, and entrances. The horizontal and vertical spot heater may be used in commercial, industrial and institutional applications. A specially designed deep-drawn venturi assures uniform air distribution The outward-drawn venturi channels the air forward for maximum, uniform air throw Outlet diffusers are provided to properly direct the heated discharge air

A 90kW unit for 240/208-volt, three-phase operation Applied as an auxiliary heat source in walkways, stairways, vestibules, and entrances. The horizontal and vertical spot heater may be used in commercial, industrial and institutional applications. A specially designed deep-drawn venturi assures uniform air distribution The outward-drawn venturi channels the air forward for maximum, uniform air throw Outlet diffusers are provided to properly direct the heated discharge air

A 5 kW unit for 208-volt, single-phase operation Designed for rugged industrial applications in hazardous locations where the possibility of explosion or fire exists due to the presence of certain flammable gases, vapors, powdered metals or dusts Permanently sealed, liquid to air, finned tube heat exchanger core Ethylene glycol water mixture used as heat transfer fluid in the heater core, providing -45°C, (-49°F) freeze damage protection High-performance electric motor driven fan blows air across finned tubes to effect uniform heat transfer and area heat distribution Automatic reset capillary type high limit provides high temperature regulation and is rated for 100,000 cycles of service Adjustable louvers allow directional control of air Can be wall, ceiling or floor mounted

A 5 kW unit for 208-volt, single-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor

A 3.3 kW unit for 208-volt, three-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor

A 5 kW unit for 208-volt, three-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor

A 10 kW unit for 208-volt, three-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor

A 10 kW unit for 600-volt, three-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor

A 25 kW unit for 208-volt, three-phase operation Constructed for use in areas that require washing or hosing of equipment due to a dirty or dusty industrial environment in non- hazardous locations The totally enclosed, watertight casing made with corrosion-resistant material, makes the unit ideal for industrial heating applications 24-volt transformer and control circuit Three-position switch (off - heat - fan) Disconnect switch with enclosure interlock Capillary thermostat with stainless steel sensor Automatic reset thermal cutout Totally enclosed UL listed motor